DA40-NGX Improvement Mod (v0.9.0.1, JUN 05)

I’m getting sporadic Pitot Fail cautions, is this trying to simulate the thermal switch or something?

No one else have the issue that the state saving isn’t working? Or am I doing something wrong?

Double check and make sure that the StateSaving line is in the cockpit.xml

Right click cockpit.xml and select edit, then Left Ctrl+F then search for StateSaving.

Also, are you using the same livery each new flight? It’s my understanding that the State Saving don’t carry over to other liveries until you load a flight with the same livery again.

The other day I loaded the AC in and noticed everything was on except the engine wasn’t started, then I remembered that the last time I flew it in the sim when I quit, I had left it all running so I’m assuming state saving is working on my end.

Thanks for the advice. I’ll have to check for the state saving option in the cockpit.xml.

And yes if been flying the same livery.

You’re welcome! Also, have a look in LocalCache\SimObjects\Airplanes\Asobo_DA40_NG at the state.cfg and make sure all is well there.

[LocalVars]
broke_lmao=0
DAMAGE_OIL:1=0
DAMAGE_TURBO:1=2.2572
STATE_FUEL_QUANTITY_L=10.25
STATE_FUEL_QUANTITY_R=10.25
STATE_FUEL_SELECTOR=2
STATE_FUEL_PMP=0
STATE_FLAPS_L=0
STATE_FLAPS_R=0
STATE_FLAPS_P=0
STATE_TRIM=0
STATE_BARO=1013.25
STATE_COM1A=9349
STATE_COM1S=9349
STATE_COM2A=9349
STATE_COM2S=9349
STATE_NAV1A=4176
STATE_NAV1S=5008
STATE_NAV2A=4176
STATE_NAV2S=5008
STATE_ADF1A=143654912
STATE_ADF1S=335544320
STATE_LIGHT_STB=0
STATE_LIGHT_POS=0
STATE_LIGHT_TXI=0
STATE_LIGHT_LGN=0
STATE_LIGHT_CBN1=0
STATE_LIGHT_CBN2=0
STATE_LIGHT_CBN3=0
STATE_LIGHT_FLD=100
STATE_LIGHT_INS=100
STATE_MASTER_ENG=0
STATE_MASTER_BAT1=0
STATE_MASTER_BAT2=0
STATE_MASTER_AVI=0
STATE_PITOT=0
STATE_FUEL_XFR=0
STATE_ECU_VOTER=0
STATE_PWR_LVR:1=0
STATE_PARK=0
STATE_XPNDR=0
DAMAGE_BLOCK:1=1.259823
STATE_AVAILABLE=1

the variables are created in the system.cfg file. If you have a lighting mod or something then statw saving wont work.

I have no additional mods like lighting or something the like installed.

Ok. The state saving line is in the cockpit.xml.

I couldn’t find the folder you were referring to in your second post though. Can you point me to an exact location? This is a steam install if it helps.

Also I am using the MSFS Addons linker tool from flightsim.to. So the mod is installed on a different hard drive then the sim and then just linked into the community folder. Might that be the culprit?

Thanks again!

Nevermind. Found the folder. Al those entries are there.

State saving/loading doesn’t work for me either.

My apologies if I’m missing something obvious, but I can’t find the rudder trim? Is it in the cockpit, or a config value somewhere? I did just think about using the keyboard bindings; seems like that is working? Is that the way to use it? Thank you!

Correct, you must use keyboard bindings. You can see the trim in the G1000 EIS

2 Likes

Got it! Thank you very much @MrTommymxr ! Really appreciate the work you do on this, it’s a lot of fun to learn and fly this plane.