Button pressed - Send B:SAFETY_AIRFRAME_DOOR_CARGO_KEY_PUSH-Event
Button released - Send B:SAFETY_AIRFRAME_DOOR_CARGO_KEY_RELEASE-Event
Or put both B: events in Button pressed.
1 Like
hmmm, where to find the file? The one on flightsim.to seems to be without the display.
Thanks for responding.
You need at least version 11.2.0.4 ! I did not tried the one on fs.to and built my own based on a different plane but would have expected that one works out, too. This is the link:
Many thanks for your helpful answer, but (always a but) it doesn’t work.
Even Debug Mode not work too.
With a switch you need to put it like this:
Switched ON:
Send B:SAFETY_AIRFRAME_DOOR_CARGO_KEY_PUSH-Event
Send B:SAFETY_AIRFRAME_DOOR_CARGO_KEY_RELEASE-Event
Switched OFF:
Send B:SAFETY_AIRFRAME_DOOR_CARGO_KEY_PUSH-Event
Send B:SAFETY_AIRFRAME_DOOR_CARGO_KEY_RELEASE-Event
In my last 2 flights, AP doesn’t follow the route. It turns the plane very irrelevant direction. Also I can’t disable VNAV mode and switch to VS mode and VNAV mode increase the altitude above the intented flight level in the FMC or simbrief.
3 Likes
MSFS Support - I have made the ticket with them.
After the update, the VNAV is completely broken, it doesn’t respect the set flight level, and it’s not possible to switch between IAS and VS modes.
It’s a shame…
2 Likes
Had this on the one flight I managed since update, locked in to LNAV and VNAV, levelled out at 21,300 (set too FL210 with 29.92-std set) changing power mode from CLM to CRZ seemed to “unlock” the AP mode’s and it 
1 Like
I guess that shouldn’t be linked in any way 
Changing to cruise power dose clear the locked vnav on clime, and lets it level out right instead of 3-400 ft higher. but it dose Not to descend on vnav at all
Yeah I got it but I am just unsure if that is a real-life behaviour…
i realy don’t know, I Realy don’t think so the Fly With Magnor video’s
I’m done, deinstalled the ATR, I’ll keep to JustFlight small commercial aircraft
Yeah VNAV at take off is broken.
While it’s SOP to arm it at take off, unless a SID has an altitude restriction (most don’t), not arming it won’t make any difference and result in a normal climb. So pressing just HDG, NAV & IAS before take off.
If it has been pressed and the modes are stuck, press the STBY pb to clear everything, then press HDG, NAV & IAS to restore AP to normal. VNAV descent seems to be working after that.
To prevent the plane going in an odd direction at take off, in the FMS press the DTO pb and select the first waypoint in the list. Now the first leg is activated and it will follow the proper route.
With these Speed Tape ™ solutions I’ve had several enjoyable flights. 
2 Likes
Nope, the PWR MGT selector should have absolutely no connection to VNAV.
Ok I’ll give that a try, pritty sure I tried the standby button and didn’t see it drop any active mode’s though
Manual correction is done by pressing STAB and then reconfiguring the AP.
Hello!
Maybe a bit off-topic,
But with AAU4 it’s said this aircraft is available in Career mode.
However I have checked I have it installed (I got the Aviator pack), checked marketplace for anything missing, still I cannot find it Career… (The marketplace says its a bundle and it does not provide information if it is working in career mode)
Anyone knows if this is in Career?
(Perhaps its bugged on my end)
Thanks!
It is not. It was said shortly after it received its 2024-upgrade back in May that it would be added to Career mode, however that has not yet materialized. No information is known at this time in terms of possible timelines for its addition to Career, or what has prevented it from being added so far.
1 Like