Hi, I have the thrustmaster airbus tca throttle quadrant. When I use the ATR the throttles do not respond at all. I’ve tried resetting them in the control setting, I’ve tried assigning an axis etc. They just don’t respond. Even on the calibration page in the aircraft, the values on the right do not change when moving the throttles. If I switch to any other aircraft in the sim they work fine. It’s as if the ATR doesn’t detect them. I’ve updated the drivers/firmware. Does anyone know what’s causing this issue? I’ve removed the gust guard but that made no difference.
Thanks
Hi, I have the same issue. When I try to calibrate to set and validate, axis values do change when I increase or decrease but as I stop moving lever the axis value comes again as if was in idle. Thanks
yeah same problem here. I don’t know how to solv it and it’s anoying the ■■■■ out of me. I just want to use it like it should be used.
Did you try to put the thrust lever axes on power axis 1 and power axis 2? DON’T PUT IT IN 0 TO 100% it didn’t work for me!
but only axis 1 and 2 solved my problem.. I hope I helped!
same problem, hope somone finds the solution
I also having issues with regular xbox controller. When i want to apply some or full throttle, is start to jump back & forth and I have to leave the button hold for a few secs so it can kinda come out of whatevwr is bugging it. Is so annoying cuz i wanna fly it so bad. Any tips would be much appreciated if possible. Already deleted and reinstalled it, no luck. Hope the devs throw a update.
I also have the problem. When calibrating in the ATR options, the tool shows values of -15000 (whatever) when the throttle is not moving. When the levers are moved, I think it shows the respective values correctly (from -15000 to about 10000). Moreover, the throttle levers in the cockpit do not move with it.
Thanks. This solved the problem. I was using the 0-100% like the other aircraft use
I have the opposite problem! Throttle working fine, flaps working fine.
On the joystick all buttons work - I use them to select camera views.
Twisting moves rudder
BUT! I cannot get the aileron or elevators to work!
Works on Fenix. And in setup the joystick moves the correct axis.
But nothing happens on the ATR!
Help please
Richard
Don’t make the same mistake as i made to manually set levers to notch & ramp positions, because they won’t get aligned with the CLB & Flex detent!
Just put the TCA lever into CLB detent and set notch, same for Flex and ramp.
It took me a few tries before i found out pressing “Validate” is not enough you also have to press “OK” before the new changes are applied
Sorry if I am been thick here but I am unsure what what you mean.
When I calibrate and I move the throttle it does change the raw value.
The exact same problem that appeared to me today. So out of nowhere, the plane worked until yesterday, today, without having touched anything, or put new addons, nothing at all, aileron and elevator axis, they no longer work, or rather, the sim sees them correctly and even on all other planes work, not on the atr. This is a big problem, because it effectively makes it impossible for me to use the atr. I’ve been doing a lot of tests all day, but they don’t lead to anything, now I try to completely remove the atr and reinstall it from scratch, hopefully it works.
If you’re interested, I’ve made a specific topic, maybe you can comment too, so there are already two of us with this problem. I tried everything to solve, but nothing, there’s no way. Something never seen in many years of flight simulation.
This topic…
THE SAME TO ME TODAY WITH THE EW UPDATE OF ATR Asobo 600 72
dOESN´T WORK AT ALL THE tca tHRUSTMASTER tHROTTLE. I was work fine before the update of the ATR and now, suddenly doesnt work menawhile flying after take off:
I 've configured using the PAD of Asobo again and work well while taxi, and take off, but when i try to move the Throttle without using Autopilot or the autopilot on .. get stuck and the Throttle doesnt work at all.
I try two times starting from beginning a new fly and always the same… it’s frustrating…
efore the UPdate of ATR from Yesterday, all was fine…
This is pure junk!
Any solution? Anyone happens?
thanks for your answers!
Thanks!
Same for me, after take off no response anymore.
I have the same problem, help please
It’s working for me when I don’t use the Idle Gate Lever, but that is not the normal procedure (I think???)
Is there any update on this topic. TCA Airbus throttle still broken, stops working after departure
I tried the solution mentioned and I am encountering the same problem. My raw input values on the ATR’s EFB start at -15823, when i move the throttle, the values change for a very brief moment and then return to -15823, no matter what throttle position i set it at. Like others have mentioned, the throttles work great on other aircraft within the sim. I’ve tried recalibrating the throttles via Thrustmaster’s software, I’ve tried creating new profiles within the sim for sensitivity, I’ve double checked to ensure there was no other buttons mapped to throttles within the sim. The only thing that seems to work is mapping the keyboard for the throttles. Looking forward to seeing a solution.