Boeing 707-320C and Thrustmaster Hotas Warthog Configuration

I’m trying to use this aircraft but I’m stuck on the throttle setup and cannot leave the stand. I have a Thrustmaster Hotas Warthog which has two throttle axis and I want to use engine 1+2 on my first axis and 3+4 on the second.

Below settings will allow me to use the throttle from 0-100, very strange I have never had these settings before! I have to set Neutral to 1 or else the throttle in the cockpit wont move until I have moved my throttle lever halfway. Is this normal?

image

image

image

Also, I cannot get reverse thrust to work. I have these set (due to the stupidly large font in the GUI it is not possible to see all text for the options):

When pressing HOLD THROTTLE REVESE THRUS(t?) the revers on the engines are not opened until I have moved my throttle control halfway. I do not want to have reverse thrust on the axis and there seems to be no option to set this.

I have to issues with any other aircraft. Any help is appreciated!

There’s also a THROTTLE 1 AXIS variable without the (0-100), this is what I use on all my planes.

I believe TOGGLE REVERSE THRUST is what I use for reversers, and what happens once you’ve pressed that button, you have to increase throttle to increase reverse thrust, then you press the button again to get into normal thrust, this works fine for me. Perhaps having both TOGGLE REVERSE and HOLD REVERSE enabled causes some conflict? I would also look at throttle sensitivity in the settings, maybe there is an overly large deadzone applied to it.

Another thing you can do is map a button to a variable it’s called something like DECREASE THROTTLE, if you hold the button starting at idle, reversers should engage, and reverse thrust should increase until you release the button, or you reach max reverse. then simply moving your throttles out of idle will stow the reversers.

Ok, I have never understood the difference between THROTTLE 1 AXIS and THROTTLE 1 AXIS (0-100). Using THROTTLE 1 AXIS seems to work better without having to fiddle with the input curves.

I’m not sure though if reverse thrust will work though. Now when the engines are off nothing happens when I press HOLD REVERSE and move the throttle lever. Shouldn’t the upper levers above the thrust levers move or is that not modelled? Or maybe I have to start the engines?

Nothing to do with the aircraft, but the “stupidly large font” is adjustable, on the Accessibility page.

73

No, it is not possible to decrease the font size, the minimum allowed value is 18 which is way to large for my widescreen. There is a separate thread about that issue, it has been like this since the sim was released.

It does use the

You engage these buttons then increase your hardware’s throttle levers.
It can be “fussy” to get to work correctly!

Yes, you can also bind two or more engine throttles to the same lever on your hardware.

Just landed at LIRF and reverse thrust worked! Interesting aircraft but I did a lot of trial and error during the flight! I guess I have to read the manual! :notebook_with_decorative_cover: :smiley:

Hi @Swede001
I’ve created this topic for you so that users can continue to offer assistance without derailing the feedback topic for the 707.

I also had trouble with the reversers initially, I think the reverser handles doesn’t work with engines off, can’t remember specifically.

you can increase the size of the controller settings window to see it all, or pop it out which seems to have a smaller font.

Yes, I popped it out, moved it to my second monitor and maximized it. When trying to scroll in the lists using the mouse wheel the camera in the cockpit on my main monitor zoomed instead of scrolling the list in the control window.

Anyway, my throttle settings seems to work now with all the help I got here so hopefully I won’t have to touch that controller window for a long time!

Glad to hear everything is working now, if you haven’t checked, I was just loading up for flight to PHNL, I can now confirm reverse levers do not move if the AC is unpowered.