Didn’t work for me earlier in 1.1.4.
What’s not working? I’m using v1.1.5.
Here’s mine from a few mins ago.
It also I think (difficult to tell in bright lighting) illuminated the orange DH lamp on the pilot’s side at DH. Is it meant to do more than this?
1 Like
it also illuminates one of the FMA lights on the warning panel when you hit selected height. It does not (and never did) play a sound.
I will reinstall and report later.
Ok thanks I wasn’t sure if it ever did (I switch between a lot of aircraft, many of which do). Radio altimeter seems to be working for me so I’m not sure why some are seeing an issue.
Try an uninstall from windows->settings->apps->installed apps
I do this every time before a reinstall. I know the installer of the new version is supposed to do this too, but maybe worth checking for any old versions kicking around. 
1 Like
Light works when I hold test, but the needle doesn’t move, and I’ve confirmed the RA is turned on via the switch. I’ll test 1.1.5 tomorrow.
Still no radio altimeter after reinstall.
The issue only with GNS530. Moreover - I have red flags on art.horizon:
Is there an OAT gauge anywhere in the cockpit?
Its just to the right of the top engine gauge.
Impossible to tell with the tiny screenshot, but they look like GS flags to me, identical to the one on the HSI, which would be normal on ground.
It is confirmed issue with GNS530 version.Will be fixed soon I guess.
1 Like
You need to report on their discord. I haven’t tried the GNS530, I’m using the free PMS GTN750.
They also don’t seem to have an official bug logging secrion or anything as it’s early access.
1 Like
Wow I love this plane! After years of flying Citations in all the sims, this is much more fun! In real life I’d probably want a Citation, but this is so much more challenging. The only struggle I’m having is getting my CH Yoke and my Bravo buttons to work. I know MSFS has the worst controller setup ever - but this plane is a real challenge. Along with FS locking up after changing a few settings and having to kill the app and start over 
My main problems are elevator trim, engine reverse, AP off, etc. etc.
Thanks for any guidance!
2 Likes
I assume you are not using Spad Next or similar otherwise you wouldn’t have any problem with your bravo.
If this can help here are few recommendations:
You can bind the reversers on the Bravo to “decrease throttle 1 & 2” this will work always and better than needing to toggle the reverse and then advance the throttles without being sure if the reversers are deployed or not. You can either do that with the bravo reverser levers or with the cutoff position for the throttles, both work fine. (remember to arm the thrust reversers in the plane first of course)
For the switches in the Bravo I would recommend you to clear them all as in the Bravo they are always sending a commend and that can cause problems, the bind them to whatever you want making sure only those are bound.
Make sure to bind these:
SMOKE ON / SMOKE OFF: Map these to the same button, one “On Press” the other “On release” this is the manu button of the AP you can press it and while holding it adjust pitch then release and the plane keeps that pitch.
G LIMITER ON / G LIMITER OFF: Same, map to one button one on press and the other on release, this is will give you two funcionalities while on the ground you can keep it pressed to turn nose wheel steering on, in my view it is much better than having it permanent on. In the air a press will disengage AP and Yaw Dumper so you press this before landing.
Hope it helps!
2 Likes
Absolutely love this bird, it’s likely my most favorite in the sim right now, and I have never been a BizJet fan… until now.
3 Likes
The same here. I’ve always thought I’m purely an airliner type of guy but now I’m also hooked to one military aircraft (Avro Vulcan) and one bizjet (this Learjet beauty).
2 Likes
Well, it should be that gauge next to the turbine speed gauges but I think it’s not correct and shows rather TAT than OAT.
There’s a page in the EFB where you can get OAT and it seems true to reality.
Thank you for this detailed reply! I’ll give them a try.
Are these in Spad because I don’t have any of these settings in my Spad