software his here
go to site support.thrustmaster and below page, you find software and download for quadrant and joystick
I hope this link and explanation works for you - download the pln file and rename it to pdf. When following the calibration instructions, you need to add and extra step between steps 7 and 8 - the CLB detent and the Full Reverse Stop. You need to enable the reverse thrust latches to stop you at the idle detent, where you need to also press the red buttons on the levers, before then lifting the latches and moving the thrust levers to full reverse stop and the final button presses.
1 Like
Thank you Mousketeer i will try
The same for me, any solution.?
2 Likes
Iām gobba take a look it tomorrow
Can you break the fix a bit better as its really confusing. Iām gonna take a tip from a other gentleman in adjustments in the settings then if thay doesnāt work ill try it your way.
Can you make the steps for fixing it step by step so we can all see what we need to do. So basically can you write it down clearly step by step with pictures hopefully so everyone will know exactly what we all have to do. Thanks
Thank you for your configuration. Copied it and I am quiet satisfied!
One question though: When my throttle levers of my quadrant are in the CLB position, I only have 80.4%. I have to push the levers a little bit more forward to get your 89%. Do I have to enter a lower DetentClimb value to compensate this?
Perfectly working for me now using this setting:
1 Like
Thank you thank you thank you, you save my christmas night. Y settings is perfect for me. Happy christmas.
1 Like
Hi Neo, I dont find the Work Folder in packages/community for throttleconfiguration ini
Where is iit plz
Itās not in Packages\Communityā¦ Itās in Packages\a32nx. You have to go one level outside of the Community folder. Inside of Packages\a32nx, thereās the Work folder inside it.
You can only get this folder to appear when you download and install the Custom FBW version, not the Development version. And you start a flight on the A32NX mod at least once, to get this folder to appear.
This is mine on the Steam version.
Thank a lot
Merry christmas !
Ok Iām not on steamā¦ So that the way!!!
I gonna looking for !!!
Good evening Sir Neo4316
Thank you, I followed the progress of your installation, itās much better than before, should I calibrate my quadrant like in the video youtube " How to calibrate your TCA Quadrant Airbus Edition"
Thank you for your answer
I take this opportunity to wish you all a MERRY CHRISTMAS !!! 
Yes, you have to calibrate your quadrant according to the video.
However, thereās a step missing in that video. So instead of stopping at pressing the side buttons at the IDLE detent last, you have to add another step where you unlock the latch and move your throttle to full reverse, and press the red buttons again. This is to ensure all detents are properly calibrated. Then continue with the rest of the process.
TM forgot to add that last part in, which caused other issues. You calibrate this properly with that additional step I mentioned above, and your throttle would not only engage properly, but they would also be properly aligned with each other.
1 Like
thank you i will try
This post helped me setting mine up a lot today! Thank you!
Question - where did you get the 1.61 firmware? When I click check for updates it says Iām on the latest with the 1.56. I also did a full reinstall using the download on the TM website.
Only issue Iām having is the throttles donāt read idle at the idle detent. Iāve adjusted the throttle config ini file to compensate for it but it would be good to get the full range of motion.
You install from here: Thrustmaster - Technical support website
Itās under Drivers. Install the Drivers - Package 2020_TFHT_5 + Firmware
Once you do, Open your start menu, and look for Thrustmaster TM Flight Series ā Firmware Update and run it. Once itās open, select your hardware, and select the firmware, and you can update the firmware.
The Check for updates from the control panel doesnāt seem to work. So itās pretty useless. You have to use the separate Firmware update app to do it. Once you do, continue with the factory recalibration proocess after itās updated to firmware 1.61
Nah, as long as youāre updated to firmware 1.61 and do a proper full calibration (note that the official thrustmaster guide to do factory calibration is missing a step at the end. Once you reach the part where you press the two red buttons on IDLE detents, you have to lift the latch and move the throttle to full reverse and press the side buttons there as well. Then you can continue with saving the calibration settings by pressing the two black buttons and continue with the next process.
Then use my original throttle config ini that I posted in that other thread. That should get things working for you.
1 Like