OpenXR Toolkit (upscaling, world scale, hand tracking...) - Release thread

How did you set the IPD per eye correction? Purely subjectively, by observing the image in the headset?

Well, I knew my IPD from when I needed glasses. That serves as a starting point. I then adjusted the horizontal and vertical offset for my divergent right eye bit by bit until it became clearer and more comfortable. It wasn’t much +1.8 horizontal and +1.9 vertical.

However, and this is important, once you have dialed in your IPD and any correction for non perfect eye alignment, there is another correction that needs to be made and that is to adjust the stereoscopy of the headset so that it matches the real world for you. This will give you the best and most accurate 3D effect in your mind. The video linked below shows how to do it.

Pimax IPD Tutorial

Could anyone familiar with toolkit and is aware of this MQSR( Meta Quest super resolution) capability provide some insight as to whether it can be leveraged in the future?

Referring article: New Meta Quest Super Resolution provides sharper graphics

Been playing around for a few hours now trying to get the imagery to look as realistic as I can and have finally settled on these settings. I believe setting Vibrance to 0 was key.

Brightness: 55
Contrast: 50.35
Red: 33
Green: 38
Blue: 52
Exposure: 40
Saturation: 34
Vibrance: 0

Great, been looking for a new color config. Will try it, thanks!

What headset are you using these with?

Oculus Quest 2 with RTX 3090

Hey guys I have a question that I’d assume some else asked before me but couldn’t find anything using search function.
I have 3080ti that comes with 12GB of VRAM. Why does in advanced FPS counter view shows that I have only 10GB. I’m assuming that since at, let’s say, 9GB VRAM used it says that 90% of VRAM is used.

Been asked a million times :slight_smile:

10GB is the amount that is usable, the other 2GB is reserved by the OS. Any application going above the 10GB and eating into the OS reserve is baaaaad and will likely ruin your performance.

thnx. I was really looking before I asked. I don’t like the search function in this forum…
Anyways, thank you for the answer and for all your work!

When the Varjo Aero is run with foveated rendering at the highest resolution (39ppd), it specifies 1200x1200 + 2192x1880, I guess that’s inner and outer zones.

Does anyone know how exactly the OXRTK’s resolution override affects this? Does it just scale both zones up by some proportional amount? Or does it only affect the inner zone or…?

This is the Varjo foveated mode (aka quad views) resolutions and this is not used at all in MSFS.
If you start MSFS and go back to Varjo Base while in VR, you will see this setting show “Stereo” and those 2 resolutions are gone too.

Look at the tables under “Image resolutions” in this page to see the PPD to resolutions (table 3 is for stereo)

ooohh OK, thanks for the quick reply!

I guess that means OXRTK does it’s FR completely independently of the quad view setting shown in Base. Good to know!

So where exactly can the quad views actually be used? I think DCS, anywhere else?

Yes Quad Views is something that only the game can implement. OpenXR Toolkit instead uses Variable Rate Shading, which can be injected even without cooperation from the game.

DCS and Pavlov VR are the only 2 games to my knowledge today.

Gains are massive, we’re talking doubling FPS with no noticeable quality loss. This is how foveated rendering needs to be done!

I have the Crystal for a few days now and I have to say, the more I use it the more I am impressed by the picture quality!
Flights in the Crystal feel completely different to me than when I did the same flights in the G2.

The Crystal is my 3rd headset. My first was a Oculus CV1, the 2nd a Reverb G2 and now the Crystal.

The upgrade from the G2 to the Crystal for me feels just as substantial as when I went from the CV1 to the G2.

The only negative thing about the picture in the Crystal is that they chose the “extreme” setting as default for the local dimming.
This setting can lead to very weird effects in the cockpit at night depending on how you set up your cockpit lighting.
However, once I changed the “exteme” setting to “balanced” those issues went away.

Can somebody let me know the location of the config file for the Pimax where you can manually fine tune the local dimming setting?

C:/users/your user name/appdata/local/Pimax/runtime/profile.jsn

Be aware that there is a bug in the Pimax client that messes with some saved values, such as colour corrections and fine tuning of IPD offsets. It hasn’t messed with local dimming black level for me though.

Thank you!

@mbucchia Hey Matt, quick question… I’ve just done a reinstall of my PC and am looking through my backup image as to where my OpenXR TK settings would have been saved prior to the rebuild. Are they saved locally in a file or the registry?

Any help appreciated!
Cheers

Steve

They are stored in the registry.

HKEY_CURRENT_USER\Software\OpenXR_Toolkit\FS2020

Thank you!