Try checking your trim before taxi, I think there was bug in the sim that starts rolling your trim either +/- in 3rd party aircraft.
Thanks for the help…
I’ll watch the video tomorrow and set mine up along with it.
I’ll have a look at my trim also…
Hi,
Concorde help needed.
Can someone help me with regard to use of the Nav radios? Specifically to do a STAR and ILS approach to Rwy 27R at London Heathrow EGGL.
I get confused with how to set up the Nav1 and Nav2 radios and using the Instrument changeover switch from CM1 to CM2. I am not sure what function the 2 Nav Standby displays have as putting the ILS frequency of 110.30 in there does not bring up the loc and g/s. It appears I have to go to the FMS and put in 110.30 there under NAV1 to be able to fly an ILS approach.
My practice routine is to do a normal take off from Rwy 27R and climb on rwy hdg to 4000 ft. Then tune up 113.75 BNN on the Nav 1 FMS slot. This way I get a DME to BNN and can track to it. I descend to 2200 ft at 220 knots. I then fly the 127 deg radial out to 18 DME. I then lower nose and gear before the turn to intercept the 269 radial on the London VOR 113.60. To do this I again visit the FMC and change Nav 1 slot to 113.60 to track inbound to Rwy27R. At about 7nm I again visit the FMC and change Nav 1 to the ILS frequency 110.30. This way I get the glideslope and localiser which I can hand fly or select VOR LOC and GLIDE to get back onto the runway.
I am sure there must be a way to do this perhaps by use of the nav standby settings windows and the co pilots instrument radio settings to save all the fluffing about with the FMC.
What is the method DC means us to use. I have obviously missed it.
Much obliged,
Peter C
Hi, you just caught me as I’m about to leave for a weeks’ holiday and won’t be able to respond here! I just use the main radio box in front of the pilot - select required FREQ, make sure it’s active ( FMC will confirm automatically on its display ) and then make sure you’re in RAD mode ( not INS ) to detect radio navigation beacons. Simple as that really. HSI and ADI will present any ILS and course deviation / DME data. I rarely if ever use the FMC.
Hope this helps ![]()
As Dean said, the drums show the nav1 and nav2 standby frequencies. If you do from there, tune the Stby frequencies and swap them to active by pressing the swap buttons. however if you do from Radionav in the fmc it is more direct. In order to follow the STAR you need to be in INS as is still a GPS route, but to capture the LOC or the GS you need to be in RAD mode before using VORLOC, GLIDE or LAND within the area. Normally by pressing one of these buttons when the frequency has LOC or GS should swap to RAD mode automatically without you needing to do the change manually. Trying to capture a LOC or GS will ignore the STAR, so I normally do all the STAR first before going from INS to RAD.
Hope it helps.
This happens to me as well, the first few times I went off the runway and crashed in a spectacular fashion, then I restarted and it worked fine with the identical setup. Also happens to me in the new Darkstar as well, in free flight, good times…
(On Xbox)
Hello there
I’ve several rewarding flights with this awesome plane! and love it !
I wonder if Interconnect valve 6-7 and 5-8 are working because I can’t get these tanks balanced when they are not balanced ?
thanks for your support
Hi! the ICValves work but the fuel flow between them is gravity based, there are no pumps between them regulating. In addition, given the position and volume of the tanks, its balance is not based on having the tanks at the same level of capacity, that means that an imbalance is not based in have the tanks 5,6,7,8 with different levels. You shouldn’t worry about it. Anyway the fuel system in SU9 is bugged and recognized by Asobo. I can’t make many changes until they release a fix.
FuelSystem: Problems with Junctions in Su9 - MSFS DevSupport (flightsimulator.com)
Thanks for the quick reply ![]()
it’s clear !
Even with a big difference between tanks (ie 5@100% and 8@10%), it seems to have no gravity fuel moving with SU9.
Look at the fuel tank diagram. The tanks are not the same size so they are not going to hold the same amount of fuel. In fact, if they did hold the same amount of fuel the plane would be OUT of balance.
Cheers guys and thanks for the help. I just did my first successful circuit. Flew out to BNN. Tracked to 19nm DME ON THE 127 radial, turned right to intercept the 270 LON radial and then intercepted the 27R ILS. I guess the main thing for me is I was reading the frequency on the Standby Nav radio drum as the active. Of course the active one is hidden and it is showing what your next frequency will be once you hit the swap button.
PC
Glad you did it. As there aren’t native events to directly fix or set active frequencies, that’s why the drums or knobs are working on Stby ones instead. Anyway I think I have this issue sorted for the next update with custom events, but it also requires a decal texture work to erase Stby in there.
You can also enter/check your active freq in the ins (fmc) under rad-nav page. Personally I find that more convenient than turning it on the dial and press swap button.
Yes. I do check the FMS but now that I am comfortable with it I just use the Standby Nav drum to set up my flight. For these practice circuit flights I am not using a flight plan. I can get airborne and right turn towards BNN at 2500ft. Track the 127 radial to 18nm whilst sorting out the droop and landing gear. Change to HDG Hold and tune LON VOR before tuning the ILS for 27R. All on the standby Nav. Where I come unstuck though is the MSFS auto pilot is really hit or miss. Sometimes I get airborne , off with the reheats and set airspeed and altitude ACQ with 1 AT and 1 AP engaged. But I have to then coax the aircraft to follow what I want before it settles down and behaves itself. At the other end turning towards the runway with the ILS tuned in at about 12nm out and doing 195 knots the autopilot doesn’t want to turn to intercept the localiser and Glide wont descend when we meet the G/S or it goes to the other extreme and heads for the ground well short of the threshold. Definitely in RAD mode. What procedure do you guys use to intercept and get the Concorde to latch onto the LOC and G/S? I am probably doing something wrong. I prefer not to use AUTOLAND a this stage.
I tried to set up my HOTAS buttons to increase/decrease the heading bug but my button presses are ignored. And I get zero audio for the Nav radios. Marker beacons and ADF no problems. Anyone else have these issues at all? Or is just me?
What you have to always keep in mind is that to capture a localizer or a glideslope, you must not be in INS (GPS) mode. this is normally done with the switch in the RAD position, before pressing vorloc, glide or land, although it may not always work when a flight plan is active. when there is an active flight plan you can directly press the previous buttons without placing the switch in rad and the GPS will deactivate itself when the nav frequency is localizer or Glideslope (it is not our thing, it is a problem of the internal logic of msfs when it is reactivates the GPS by itself). If it doesn’t work, reset the switch again. the way to capture the GS (after pressing glide or land) is that the plane is always below the GSI, so that when the gsi needle, both in ADI and in HSI, is positioned in the center it is captured (if you are above it is not captured).
Yes I try and intercept the GS from below. One thing with some flight sims is that the ILS comes alive a lot later than in real life. Its a pity there is no audio for the ILS in MSFS. When the airport VOR is near the runway you can track in on that until the FAF then switch to ILS nicely lined up. Unfortunately the LON VOR is located offset a bit. At EGGL by the time the ILS appears you end up having to do a drastic turn to line up fairly close in. The entire flight is done with the RAD INS switch in RAD.
OK. I had a reread of the manual and I think I see the problem. I was following the Navigraph STAR and ILS 27R charts. I dont know for sure whether the real Concorde followed these but they give a course that is way too close to the airfield plus have a max speed of 180 knots for the turn onto the final approach which is way too slow for Concorde. The manual suggests being at 5000 ft and 15 miles out to capture the G/S. This I did and what do know it worked a treat. I manually put the localiser in the middle and hit GLIDE and we flew down the glidepath. At 2 miles to go I turned off the AT and AP and landed it myself.
I just had a quick question. I keep seeing references to a manual for the Concorde but I am not sure where I can get the manual from. I have not been able to find a post saying where I can get the manual. Is the manual available for customers who purchased the Concorde through the in game Marketplace as I did? I have been trying to learn what everything does by manually trying the various controls one at a time. I have been really enjoying the Concorde but there are a lot of controls to learn, especially with the detailed engineers station and a manual would be very helpful. Please let me know where I can get the manual with purchasing the aircraft through the Marketplace. Thank you and have a good weekend.
Just a quick question and sorry if this has been covered before..I dont own this aircraft but the external model seems off in some way. The passenger windows seem too high up placed on the fuselage.. is this just me or has this been noted regarding the modeling.
Look in a documents directory inside the directory where the beauty is installed on your hard drive:
..\dcdesigns-aircraft-concorde\Documents\Concorde